E510 PCI DRIVER

When removing an IDE drive data cable, grasp the colored pull-tab and pull until the connector detaches. If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. To connect a network cable, first plug the cable into the network port or device and then plug it into the computer. To guard against electrical shock, always unplug your computer from the electrical outlet before removing the cover. After you remove the heat-sink assembly, lay the assembly on its side.

Uploader: Brazilkree
Date Added: 27 July 2017
File Size: 50.90 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 88519
Price: Free* [*Free Regsitration Required]

When you install the heat-sink assembly, do not touch the thermal interface on its underside, as this may result in damage to the thermal interface material. To avoid damage, ensure that the processor aligns properly with the socket, and do not use excessive force when you install the processor.

If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you install your new processor. To avoid damage to the drive, do not set it on a hard surface.

Memory purchased from Dell is covered under your computer warranty. Reversing the cable prevents the drive from operating and could damage the controller, the drive, or both. Remove the card before connecting the pck cables. If you are installing or replacing a card, follow the procedures in the next section. Otherwise, your computer may not start properly.

Dell Dimension

You can do so by touching an unpainted metal surface on the computer chassis. Most interface connectors are keyed pxi correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other connector. You must position the processor correctly in the socket to avoid permanent damage to e10 processor and the computer when you turn on the computer. Snap the bracket onto the new drive. To avoid damage to the memory module, press the module straight down into the connector while you apply equal force to each end of the module.

Related Drivers  PCI VEN 10EC&DEV 8119 DRIVER

To guard against electrical shock, be sure to unplug your computer from its electrical outlet before installing any cards.

If the module is difficult to remove, gently ease the module back and forth to remove it from the connector. To loosen the two captive screws on each side of the ppci assembly, you need a long Phillips screwdriver. To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any e5110 your computer’s electronic components.

If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure. Despite having a plastic shield, the heat-sink assembly may be very hot during normal operation. Grasp the card by its top corners, and ease it out of its connector. Ensure that the assembly has had sufficient time to cool before you touch it. Gently pull the securing tab, pxi the card by its top corners, and then ease it out of its connector.

The mounting-bracket screws need to be removed for the removal of the system board. You must route these cables properly when you replace them to prevent them from being pinched or crimped.

When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on the interface cable is oci master or boot device drive 0and the device attached to the middle connector on the interface cable is the slave device drive 1.

Related Drivers  HP 8660 PRINTER DRIVER

Removing and Installing Parts: Dell Dimension /E Service Manual

If the card is not removed correctly, the system board may be damaged. See the documentation that came with the card for information on configuring the card, making internal connections, or otherwise customizing it for your computer.

Do not route card cables over or behind the cards. Cpi you are adding a floppy drive, see ” Installing a Floppy Drive. If you are not installing a processor upgrade kit from Dell, reuse the original heat-sink assembly when you replace the processor. If your computer includes a card retention mechanism, remove the top of the retention mechanism by pressing the tab and pulling up on the top.

DDR2 memory modules should be installed in pairs of matched memory size, speed, and technology. When installing the heat-sink assembly, do not touch the thermal interface on its underside, pcl this may result in damage. Some network adapters automatically start the computer when they are connected to pxi network. If necessary, disconnect any cables connected to the card.

For additional information on the type of memory supported by your computer, see your Owner’s Manual.